Thermal Fatigue Behavior of Ni_3Al Based Superalloy IC6E

The thermal fatigue behavior of Ni3Al based superalloy IC6E during the cycles between 900 ℃/1 000 ℃ and the room tempera-ture was investigated. The experimental results indicate that the primary and secondary thermal fatigue cracks initiate inside or round the borides and then spread away along grain boundaries and/or in interdendritic areas. The fracture of borides and their separation from the matrix at interfaces are mainly responsible for the crack initiation and its spreading. At temperatures higher than 1 000 ℃, the grain boundary oxidation combined with cyclic stresses accelerates the crack growth.     

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.     

TC6钛合金棒材热处理工艺研究

对TC6钛合金φ20mm～φ120mm不同规格棒材进行了普通退火、双重退火、等温退火、固溶时效等热处理方法和热处理制度研究,并对比分析了热处理制度和组织、性能之间的影响关系,结果表明,TC6钛合金的组织和性能对热处理工艺敏感,应根据半成品规格、类型、截面形状、使用温度、受力情况以及设备条件等诸多因素选择合适的热处理方法和制度,才能达到强度、塑性和韧性的最佳匹配。研究结果证实普通退火是一种简单易行的退火制度,适用于飞机结构用中等规格棒材等半成品的退火,进一步提出了TC6钛合金棒材的热处理工艺选择原则。     

2D70铝合金热稳定性研究

2D70是可热处理强化的耐热铝合金,一般用在高温场合.以2D70铝合金自由锻件为对象,研究了热稳定化处理对合金室温、高温拉伸性能的影响,测定了合金的高温持久、蠕变性能,并观察了合金在这些高温试验条件下的组织变化.结果表明,2D70铝合金的耐热性较好,可在150℃长时使用,175℃以下时,合金的性能和组织变化都不明显;高温下合金的断口呈现沿晶断裂特征.     

钛合金板材激光弯曲成形的研究

 对常温下钛合金板材进行了激光弯曲成形研究。分析了激光功率、扫描速度、光斑大小对板材弯曲变形的影响,获得理想工艺参数范围为:功率1 .0～1 .2 k W、扫描速度2～3 m/min、光斑直径6～7mm。同时分析了板材厚度、宽度及扫描次数对材料弯曲变形的影响,为钛合金板材弯曲成形提供了一种新途径。     

热暴露对B/Al复合材料性能的影响

对经300℃、500℃高温热暴露的B／Al（LF6）复合材料的力学性能进行了研究，实验结果表明材料在300℃下热暴露时，性能下降速度较慢，100h后强度保留率约为76％，延伸率保留率为74％。而在500℃下热暴露时，5h以上强度就有明显降低。高温长时间热暴露后复合材料的断裂也从积累型转变为典型的非累积型断裂。通过透射电镜（TEM）及扫描电镜（SEM）对固态热压制造态和主温热暴露的界面状况进行了分析，认为界面反应是造成B／Al复合材料力学性能下降的主要原因。     

ZrO2陶瓷热障涂层显微结构及隔热性能研究

用电子束物理气相沉积法(EB-PVD)在DZ125高温合金上制备Y2O3部分稳定化的ZrO2(YSZ)陶瓷热障涂层,并用扫描电镜(SEM)观察涂层显微结构.采用激光脉冲法对EB-PVD热障涂层的热扩散系数进行测试.为防止热扩散系数测试时激光穿透ZrO2陶瓷层,在试样表面制备不同材料的遮挡层.结果表明,EB-PVD热障涂层呈明显的柱状晶结构,柱状晶垂直于涂层/基体界面.基体的热扩散系数随温度的升高而急剧增加,陶瓷热障涂层的热扩散系数随温度的升高呈下降趋势,但变化幅度不大.室温下陶瓷层的热扩散系数小于基体的1/3,1200℃时约为基体的1/67.试样的激光遮挡层很好解决了激光脉冲法测试涂层热扩散系数时的不稳定性和激光穿透问题.在满足遮挡要求的条件下,遮挡层材料种类对热扩散系数测试无明显影响.     

环氧树脂和双马树脂的热水老化及弯曲性能研究

对环氧和双马树脂进行96℃热水老化处理后,再经60℃恒温干燥脱水处理。分别测量了两个过程的吸水率、脱水率与时间的关系,计算了它们的平衡含水(脱水)量M∞、扩散系数Dx、动力学参数k和n、渗透系数P,阐明了两种树脂的吸水和脱水过程均源于扩散。其次,比较了两种树脂的弯曲性能,实验结果表明经热水老化的两种树脂性能明显降低;干燥脱水能使树脂弯曲性能得到恢复,但依然低于树脂的初始性能。     

热暴露对IMI834近α高温钛合金组织和拉伸性能的影响

测试了ＩＭＩ８３４高温钛合金在６００～７５０℃的空气中热暴露１００小时后拉伸性能，利用透射电镜和扫描电镜观察了合金暴露前后的组织变化及拉伸断口，认为表面氧化是造成合金热暴露后塑性下降的主要原因，但基体组织内有序α２相和硅化物的析出变化也在不同程度上造居了合金热暴露后的强度和塑性的下降。     

Microstructure and Martensitic Transformation Behaviors of Explosively Welded NiTi/NiTi Laminates

The study is a first attempt to prepare bulk NiTi/NiTi shape memory alloy (SMA) laminates with a macroscopic heterogeneous composition by explosive welding and investigate their microstructures and martensitic transformation behaviors. After explosive weld- ing, a perfect interfacial bonding between the two components and a reversible martensitic transformation are realized in the tandem. Results show achievement of a fine granular structure and the maximum value of microhardness near the welding interface because of the excessive cold plastic deformation and the high impact velocity during the explosive welding. Meanwhile, the effects of aging on the transformation of the welded tandem are investigated by differential scanning calorimeter (DSC) and subject to discussion. The trans- formation temperatures of NiTi/NiTi SMAs increase with the rise of the aging temperature. The experimental results indicate the shape memory properties of NiTi/NiTi SMA fabricated by explosive welding can be improved by optimizing the aging technology.